FTC Championship: Day 3

Day Three

On Thursday we played three matches. In the first match the scissor lift wire came undone and therefore we could not actually score balls. In our second match the robot finally worked properly. We scored in the medium goal in autonomous and scored more in the medium goal later in tele-op and filled the centre goal in end game. Although we did well we still lost the match. In our last match of the day, our autonomous program didn’t work, but we still won the match.

Tonight we had dinner with the teams from the Pacific Northwest, went to the FIRST Opening Ceremonies, and cheered for Katie and Duncan at the Dean’s List Ceremony

Livestreaming from Championship now available

The livestreaming link is: http://livestream.com/accounts/13199388/FTC-Edison (our team is in the Edison division)—we will email around a more detailed schedule of our matches tomorrow. We will have matches tomorrow, Thursday and Friday.

One of the tournament sponsors is SpaceX—we’re looking forward to visiting their display booth.

EV3 vs. NXT

We had an opportunity to see and handle the new LEGO MINDSTORM EV3 at the FIRST World Championships in St. Louis. We didn’t not have a lot of time to evaluate the EV3. These comments are just initial impressions from FLL and FTC team members, who have been working with the NXT for 6 years.

LEGO has posted a comparison of features between the EV3 and NXT.  The comparison includes lots of new features that we didn’t get to test.  Mostly, we were quickly checking to see what we thought for our FLL and FTC teams.  FTC has announced their competition won’t be using the EV3 in fall 2013.

[[MORE]]

The EV3 itself and its motors, are larger than the NXT and its motors. The difference isn’t huge, but if you are trying to build a very small robot, the difference is noticeable. There are two larger drive motors and then a smaller motor that can be used for attachments. The option to have a smaller motor for attachments is a good idea.

There are many new sensors, but we didn’t get to work with them enough to form an opinion.  The speakers look like they should be much better.

The software uses icons, similar to NXT-G, but they are wired more like Robolab. They can be automatically connected like NXT-G, or you can specifically wire them like Robolab.

It is Linux based, and has a different way of selecting which program to run. Likely that will just take some adjusting for people familiar with the NXT.

EV3 software screen layout seemed better. Rather than blocks down the left hand side, there were 4-5 categories across the bottom. Within each category were the actual icons.

There are four motor ports and four sensor ports. The EV3 has a SD slot so that you can increase the memory. There’s a USB hub that we didn’t get to explore. The cable to connect to the computer had different plugs.

We talked with one of the testers. The EV3 has very long turn on and turn off cycles. The estimate is 30 seconds from when you push the on button, to when it is ready to start. The NXT takes about 3 seconds.

We’re all use to laptops taking a few minutes to boot-up, but it will be harder for kids who want to push a button and get started. The extra time will add up during competitions when a team doesn’t turn their robot on, or even worse, it automatically powers down while they are waiting in line.

The turn-off cycle takes about 45 seconds. Again, it’s not a huge amount of time, but compared to about 3 seconds for the NXT, it is a significant change.

We talked to one tester who said that any time the battery was replaced, the EV3 reset the firmware and all the stored programs were gone. This ‘feature’ has significant implications for competition teams who want to have fresh batteries for each match. Many FLL teams just plug in their robot between matches, they should be fine.

FTC teams usually replace their batteries frequently at events. This ‘feature’ is a disaster for those teams. It is reasonably quick, maybe 2 minutes, to remove the NXT from the robot and pop in a new battery just before a match starts. With the EV3, the team would have to replace the battery (2 minutes), turn it back on (30 seconds), connect to a computer and download their programs again. It will easily take over 5 minutes, possibly delaying a match.

A staff person from the company that wrote the software ‘thought’ that if you waited completely through the shut down cycle (minimum 45 seconds) before removing the battery, it might not reset the firmware. Unfortunately, we didn’t get to test it.

Some of the issues with the EV3 could be fixed with a software update, but the size and battery/firmware issues are hardware and there is no easy fix. It would likely take a hardware upgrade to correct it. At this point, we haven’t decided if we will order one of the early EV3s. It’s tempting to wait 6-8 months and see how they do.